Hook up ice maker, how do i connect an ice maker supply line

Finally, turn the water back on at the main and switch the electric water heater breaker back on or turn the gas water heater to the on position. Try to run it flush against the bottom of your walls or cabinets where it is most likely to be safe. Measure the distance carefully, louisville ky and buy a supply tube with plenty of length for the job.

How to Hook Up a Water Line to a Refrigerator

How to Hook Up a Water Line to a Refrigerator From the Sink
Connect an Ice Maker to Your House with Leak-Free Fittings

Now turn on the faucet shutoff valve under the sink and check for leaks at the Adapt-a-Tee connections. Place a saddle valve onto the pipe and tighten its clamps so that it grips the pipe. Use a screwdriver to secure the clamps with standard No.

The kit provides you with the required parts to hook up a water line to your refrigerator. If you are hooking up a refrigerator ice maker, find where it is located on the appliance. If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line.

An Adapt-a-Tee is an ideal plumbing fitting for this purpose. Attach copper tubing to your cold water pipe to create a dedicated cold water line for your new appliance. Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator. If you have a newer model, it may be located in the refrigerator door. Locate the closest cold water source.

How to Install an Icemaker
How to Connect an Ice Maker Like a Pro

How Do I Connect an Ice Maker Supply Line

Drill a hole behind the refrigerator, and then one underneath the sink. Be careful during the installation process to prevent water damage, contact with electric wiring, or damage to other plumbing. Attach the water supply line with the provided compression fitting to the top of the solenoid valve by screwing it into place then tightening it up with a crescent wrench. Do not twist the nuts too tight as this could damage the supply valve, sites the supply line and the adapter. Did this article help you?

Run this line to the back of your refrigerator or under-counter ice maker and secure it with a compression joint. Measure the distance between your ice maker and the cold water pipe before purchasing the copper tubing to get the appropriate length. This will help you narrow down what model of ice maker to purchase.

EHT Spotlight
Ice maker hook up

How to Hook Up the Ice Maker on Your New Refrigerator

Get video instructions about kitchens, bathrooms, remodeling, flooring, painting and more. Turn off the main water valve before starting your project by turning it clockwise. Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink.

  1. Insert the new water line into the opening on the tee.
  2. Install the Valve Now that the water's off, install the new valve for the icemaker water line.
  3. Connect the Supply Tube to the Refrigerator.
  4. Avoid leaving the tubing somewhere it might get damaged, stepped on, or crushed.

Connect an RO System to a Refrigerator or Ice maker

If there is no water dispenser, throw away the first full batch or two of ice to make sure it is all clean and ready to use. Now move to the back and install the fill tube. If so, your job is very easy.

An ice maker would be well-located under your kitchen cabinet to the side of your sink or refrigerator. Put the ice maker into its place under the counter. Locate the ice maker on your refrigerator.

How to Connect an Ice Maker Like a Pro

  • The tee adapter connects to the water supply shutoff valve.
  • To make this connection simple, drill dime-sized holes into the sides of your cupboard with an electric drill to easily thread the copper tubing through it.
  • Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher.

Attach a saddle valve to a clean spot on the cold water pipe. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. Watch for leaks at all the connections. You will need to install a cold water line for either a refrigerator ice maker or an under-counter ice maker.

If there are no fixure shutoff valves, you can turn off the water by closing the main water supply valve to the entire house. If the refrigerator has a water dispenser, flush out several gallons to purge the line of all the air. Tighten the fittings as needed, using channel-type pliers or an adjustable wrench. Tighten up the mounting screws to secure the unit to the freezer wall, promo and then add the ice bucket under the kit. You can purchase a saddle valve at any hardware store.

How to Install a Water Line for a Refrigerator

They come in various sizes to suit whatever situation you have. Already answered Not a question Bad question Other. An ice maker is a great addition to any kitchen and can be simple to install with the right materials.

Open the saddle valve to rinse through the copper piping into a large bucket. Turn the supply line on once again. Find this cold water source, which may be found under a sink, below the floor, or in a wall.

How to Install a Water Line for a Refrigerator Ice Maker

How Do I Connect an Ice Maker Supply Line - Extreme How To

Shut off the water and drain the pipe. Push the refrigerator against the wall. Wear safety goggles and gloves to protect your eyes and hands from any wood particles that may fly into the air while you do this.

Pull your fridge out to access the back of it. Adapt-a-Tees can be used in many situations where you need an extra line. Everything You Need to Know Browse a full list of topics found on the site, from accessories to mudrooms to wreaths. You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink.

She attended Tarrant County College and studied English composition. Screw the valve in to pierce a hole in the pipe. Carefully tighten the compression fitting to secure the connection. Tighten the connections slightly if you see a leak.

To install a needle valve or saddle valve, place the two clamps around the copper pipe and use a screwdriver to tighten the screws on each side to hold the valve in place. Use a compression fitting to attach the piping to the ice maker. The valve connected to the right side of the faucet is the cold water supply line.

Ice maker hookup kit
  • Nz dating indian
  • Can i hook up two external monitors to my macbook pro
  • Speed dating events in torquay
  • Jocuri cu inimi sue dating
  • Dating between boy and girl
  • Chat speed dating